Flat lay of a blush pink phone case with an ivory pearl and gold bead wrist strap, surrounded by beads, a dangle charm, pliers and beading wire on cream linen
| |

How to Make Beaded Phone Charms and Wrist Straps (3 Easy Designs to Gift)

A phone is one of the things you hold most often, so it is a lovely place to add a handmade detail. In this guide I’m sharing three beaded accessories you can make with the same few supplies: a pearl and gold wrist strap, a colorful glass bead wrist strap, and a dangling charm that clips onto your phone case.

None of these projects needs special skills. If you can thread beads onto wire and squeeze a crimp bead flat, you can make all three. I’d start with the pearl strap, since it uses one type of bead and teaches the crimping steps the other two designs repeat.

This post contains affiliate links. As an Amazon Associate, I earn from qualifying purchases at no extra cost to you. Content on Life With Amanda is created with the help of AI.

What You Will Need

  • Glass pearl beads: 6 mm ivory pearl beads for the pearl strap and the charm dangles. Shop this option
  • Round glass beads: 6 mm glass beads in soft light green (sage) and pink (blush) for the colorful strap and the charm dangles. Shop the light green Shop the pink
  • Gold spacer beads: small round gold beads that sit between the pearls and the colors. Shop this option
  • Gold beading wire: flexible, nylon coated beading wire in a gold finish that bends without kinking. Shop this option
  • Gold chain: fine gold link chain, cut into short lengths for the dangling charm. Shop this option
  • Gold crimp beads: tiny metal beads that you squeeze flat to lock the wire ends. Shop this option
  • Gold jump rings: small rings that join the strap ends and attach the clasp. Shop this option
  • Gold lobster clasps: the part that clips the strap or charm to your phone. Shop this option
  • Gold head pins: thin pins that hold the beads for the dangling charm. Shop this option
  • Gold star and heart charms: small charms that finish the dangle. Shop this option
  • Jewelry pliers set: round nose pliers, chain nose pliers, and wire cutters in one set. Shop this option
  • Phone tether tabs: thin flat tabs with a hole that sit between your phone and its case so the strap has a place to clip. Shop this option
  • Bead mat: a soft mat or tray that keeps your beads from rolling away. Shop this option

Before You Start: Check Your Phone Case

Most beaded wrist straps clip onto a tether tab, a thin flat strip with a hole that sits between your phone and its case. Some cases already have a small strap hole built in, and if yours does, you can skip the tab and clip the strap right to it. If you use a tab, a clear one blends in with almost any case.

Press the tab flat against the back of the phone before you put the case on, and make sure the hole peeks out where you can reach it.

Plan Your Beads First

Lay your beads out on the bead mat before you string anything. A simple repeating pattern looks the most polished, and it is easier to keep track of. About 25 beads that are 6 mm each make roughly 6 inches, which is a comfortable size for a hand loop. If you like a roomier strap, add a few beads, and if you like it snug, remove a few.

Design 1: Pearl and Gold Wrist Strap

Ivory pearl and gold spacer beads strung on beading wire beside a jump ring, crimp beads and pliers on a bead mat
  1. Cut the wire: cut a piece of beading wire about 12 inches long, which leaves room to work with.
  2. Start the loop: slide on one crimp bead and one jump ring, then pass the wire back through the crimp bead, leaving a 1 inch tail. Squeeze the crimp bead flat with the chain nose pliers.
  3. String the pattern: thread on four pearls, then one gold spacer, and repeat until you have about 6 inches of beads. Slide the beads down as you go so the tail stays covered.
  4. Close the loop: add a second crimp bead, pass the wire through the same jump ring, and bring it back through the crimp bead and the last two or three beads.
  5. Check the fit: pull the wire snug, but leave the beads able to move a little so the strap can flex. Squeeze the crimp bead flat and trim any extra wire.
  6. Add the clasp: use pliers to open a second jump ring, slide on a lobster clasp, link it through the first jump ring, and close it.

Design 2: Colorful Glass Bead Wrist Strap

Finished sage green, blush pink and gold glass bead wrist strap with a gold lobster clasp beside loose beads, gold wire and wire cutters on cream linen

This strap uses the same steps as the pearl design, with a color pattern in place of the pearls. Try one sage bead, one blush bead, and one gold spacer, repeated around the strap. Sticking to two or three colors keeps the look cohesive, and a repeating pattern is easy to follow while you string.

  1. Cut and start: cut 12 inches of wire and attach it to a jump ring with a crimp bead, just as you did for the pearl strap.
  2. String the pattern: repeat sage, blush, and gold until you reach about 6 inches.
  3. Finish: close the loop through the same jump ring, crimp, trim, and add the lobster clasp.

Design 3: Dangling Charm for Your Phone Case

A dangling charm is a small cluster of beaded drops that swings from the clasp. It is a good choice if you want a decorative detail without a strap.

Finished dangling charm with ivory pearl, blush pink and sage green bead drops, gold chain, a gold star and a lobster clasp beside round nose pliers on cream linen
  1. Build a drop: slide a gold spacer bead and then one bead onto a head pin, so the spacer sits beneath the bead.
  2. Trim the pin: cut the head pin about 3/8 inch above the top bead using the wire cutters.
  3. Make a loop: use the round nose pliers to bend the wire into a right angle, then roll it toward you to form a small closed loop.
  4. Make more drops: repeat to make three drops, using a pearl, a blush bead, and a sage bead.
  5. Cut the chain: cut three pieces of fine chain, each about 1 to 1.5 inches long, in slightly different lengths so the drops hang at staggered heights.
  6. Attach the drops: open the loop on each drop slightly, hook it onto the end link of a chain piece, and close the loop again.
  7. Gather the chains: open a jump ring and slide on the top ends of all three chains along with a star or heart charm, then close the ring.
  8. Add the clasp: link the jump ring to a lobster clasp with a second jump ring and clip it to your tether tab.
Blush pink phone with an ivory pearl and gold bead wrist strap and a bead dangle charm, beside a coiled sage, blush and gold bead strap on cream linen

Tips and Troubleshooting

  • If the wire kinks: a sharp kink weakens the wire, so cut it off and restart with a fresh piece.
  • If a crimp bead slips: squeeze it again with the pliers, or add a second crimp bead next to it.
  • If a bead hole is too small: test a bead on the wire before you commit to a whole pattern.
  • If the strap feels too loose or tight: remove or add two beads before the final crimp.
  • Keep it light duty: a beaded wrist strap works as a decorative hand loop, so I’d avoid swinging your phone by it and check the crimps and clasp every so often.

Gift and Packaging Ideas

A pearl strap and a matching dangle make a sweet set for a friend, a teacher, or a coworker. Tuck them into a small envelope with a handwritten note, or stack a strap and a charm on a folded card. If you do not know the recipient’s phone case color, ivory and gold goes with almost anything.

Ready to Keep Beading?

If you enjoyed making these, my beaded bag charms use many of the same beads, and these beaded keychains and car charms are a nice next project. I can’t wait to see how yours turn out.

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *