DIY Gift Card Holders: 3 Easy Paper Designs to Make for Christmas
A gift card is an easy present to give, but a plain plastic card slipped into a store envelope can feel like an afterthought. A little folded paper changes that. In this post I’m sharing three simple gift card holders you can make from cardstock in about ten minutes each: a kraft pocket envelope, a folded sleeve with a belly band, and a slotted tag you can hang on a package or a tree.
All three use the same handful of supplies, so you can make a small stack in one sitting. They suit teachers, neighbors, coworkers, hosts, and anyone else on your list who would rather choose their own gift. A standard gift card measures about 3.4 by 2.1 inches, and every size below leaves a little extra room, so a slightly thicker card still slides in without bending the paper.
This post contains affiliate links. As an Amazon Associate, I earn from qualifying purchases at no extra cost to you. Content on Life With Amanda is created with the help of AI.
What You Will Need
- Kraft cardstock: a brown kraft sheet in 8.5 by 11 inches for the pocket envelope. kraft cardstock
- Cream cardstock: for the folded sleeve. cream cardstock
- Red cardstock: for the belly band. red cardstock
- Dark green cardstock: for the slotted tag. dark green cardstock
- Natural jute twine: for wrapping the pocket envelope and tying a bow. jute twine
- Thin red satin ribbon: a quarter inch wide, for the sleeve bow and the tag loop. red satin ribbon
- Small silver scissors: a sharp, pointed pair makes the tag slits much easier. embroidery scissors
- Bone folders: for scoring and creasing every fold. bone folders
- Double-sided tape: for sealing the pocket sides and the belly band. double-sided tape
- A single hole punch: for the top of the tag. hole punch
- A metal ruler and a pencil: for measuring and marking. metal ruler
- Gift cards: one for each holder.
Before You Start: Measure and Score
Take a minute to hold your gift card against a ruler, because card sizes vary a little between stores. If yours is thicker than usual, add a quarter inch to the pocket sizes below. I’d also score every fold before bending it: press the bone folder along a ruler to make a crease line, and the fold will come out crisp instead of curved. Cardstock folds best when it is scored first, especially darker colors, where a rough fold shows white along the edge.
Design 1: Kraft Pocket Envelope With a Twine Wrap
This is the quickest of the three, and the one I’d make first if you need a dozen. Kraft paper has a warm, natural look that goes with almost any wrapping color.
- Cut a rectangle of kraft cardstock measuring 4 by 8 inches.
- With a pencil and ruler, mark a line 2.75 inches up from one short edge. Score along the line with the bone folder.
- Fold the bottom strip up along the scored line so it lies flat against the paper. This forms the pocket.
- Press a strip of double-sided tape along each side edge of the folded strip, peel the backing, and press the edges down to seal the pocket sides.
- Slide the gift card into the pocket.
- Fold the extra paper at the top down over the pocket. Wrap twine around the whole holder twice, and tie a small bow at the front.

Design 2: Folded Sleeve With a Red Belly Band
This version looks a bit more finished. A contrasting band holds it closed without any tape on the front, so the paper stays clean.
- Cut a rectangle of cream cardstock measuring 4 by 6 inches.
- Score the center line at 3 inches and fold the rectangle in half, so the folded sleeve measures 4 by 3 inches.
- Slide the gift card into the fold, with the card’s long edge against the creased edge.
- Cut a strip of red cardstock 1 inch wide and 7 inches long. Wrap it around the middle of the sleeve and tape the ends together at the back.
- Tie a short length of thin ribbon in a knot or a small bow over the band, and trim the tails.

Design 3: Slotted Tag With a Ribbon Loop
This one holds the gift card on the front like a display, so the card itself becomes part of the design. It works well on top of a wrapped gift or hung from a tree branch.
- Cut a rectangle of dark green cardstock measuring 4.5 by 6 inches. Trim two corners at the top into a gentle angle if you’d like a classic tag shape.
- Lay the gift card in the center of the tag, a little below the middle, and lightly mark the four corners with a pencil.
- Use the tip of the scissors to cut a short diagonal slit at each marked corner, about half an inch long, angled so the card’s corners can slip in.
- Slide each corner of the gift card into its slit so the card sits flat on the front of the tag.
- Punch a hole near the top center, thread a length of ribbon through, and tie it into a loop.

Tips for Neat Holders
- Test the fit first: make one holder from scrap paper before cutting your good cardstock.
- Keep the tape inside: double-sided tape along the inner edges gives a cleaner finish than glue, and it won’t wrinkle the paper.
- Write the note on the inside: a short handwritten message tucked in with the card makes it feel personal.
- Make one color family: choosing two or three colors for the whole batch makes a stack of holders look like a set.
Giving Them
A holder can sit on top of a wrapped box, rest on a plate of cookies, or go into a stocking. A stack of three tied together with twine also makes a tidy hostess gift on its own. If you give several, I’d vary the designs so each person’s feels a little different.

More Handmade Gift Ideas
If you’re building a bigger handmade gift list, a set from the DIY Christmas cards and envelope liners tutorial pairs nicely with a gift card holder. And for something people can actually use in the kitchen, the homemade coffee syrup gift set is another easy idea to bottle and give.